#Do lath and plaster walls have studs how to
#Do lath and plaster walls have studs install
#Do lath and plaster walls have studs Patch
#Do lath and plaster walls have studs code
#Do lath and plaster walls have studs series

This makes it easier to create custom curves and arches in walls and ceilings.

Lath and plaster is more contour-friendly than rigid drywall panels are.

While plaster walls are smooth and flat, they can contain slight surface trowel marks that add some desirable Old World character to a home.

Plaster is more fire-resistant than drywall.

This is why older homes are often much quieter than new homes with interior walls that are made from drywall.

The thick, dense layer of plaster dampens the transfer of noise from one room to the next.

Lath and plaster walls provide a measure of insulation, helping homes stay warmer in winter and cooler in summer.

This thickness offers some distinct benefits: In combination with the lath framework beneath, lath and plaster together comes to about 1¼ inch thick. A typical lath and plaster wall required a minimum of three coats of plaster, resulting in a dense, rock-hard coating nearly 1 inch thick. Powdered lime, sand, and fibers (often horsehair) were the traditional ingredients used in the creation of lath and plaster walls. Dense lath and plaster provides some insulation, fire resistance, and soundproofing. RELATED: What’s the Difference? Drywall vs.

If your existing home has lath and plaster walls-or if you’d like to incorporate new plaster walls in a remodeling project-keep reading to learn more about this old construction method that’s gaining new fans. Lath and plaster construction is definitely an old school technique, but when compared to drywall, it has a few surprising benefits.

#Do lath and plaster walls have studs install

You want to keep the plaster/lathe intact around the hole to prevent the plaster from cracking and falling off or the hole growing bigger than the box/coverplate.When drywall panels came on the scene in the 1950s, they soon replaced lath and plaster as a quicker, easier install option. Small drywall saw by hand will work as well if you don't use too much force. Drilling the corners of the box location will allow you to fit a narrow blade in to cut the lathe with a jig-saw, roto-zip, dremel tool. Again, taking your time will give better results with this stuff. Use a utility knife with a sharp blade to score the plaster carefully until you reach the lathe. To cut the plaster for a box I would put tape on the wall in the area where you want to cut and draw the outline for the hole on it. Dropping a weighted line or fine flexible chain through a small hole will let you know if anything is blocking the space. These are horizontal pieces of wood bracing between the studs that will block you from running wires vertically.

Running wires inside the wall is another matter. Take your time and you'll be much happier with the outcome. A little paint on the areas that are visible after mounting the TV and you're done.

#Do lath and plaster walls have studs Patch

A little spackling will patch the bad holes. It should only take a few small holes to narrow down the location and center of the stud if you take time measuring, tapping and scannning. If you don't see wood on the bit when you take it out, move over. Go deeper than the lathe to be sure you are in wood. Go horizontally with about 1/2-inch spacing.

#Do lath and plaster walls have studs series

Drill a series of holes with a small diameter bit in the area where you're pretty sure the stud is and where you want to put you anchor screws. Take some time and do all three until you have a good idea where a stud is in your target area (vertically and horizontally). Easiest way I have found to find studs for mounting heavy items is to estimate locations first by looking at existing outlets, tapping, and a deep scanning stud finder. I have a 90 year old house with same walls. Do you think that I could get away with 1 stud? It is after all only 80lbs and cheez has his on hooks not even in studs Last time I attempted to install a outlet box in the wall it was a disaster. My 2nd concern has to do with drilling out the lath so that I can run wires.

#Do lath and plaster walls have studs code

Any suggestions?įrom what I understand, code at the time was studs are 16 inches apart. I guess I could use the old guess and check method but I would like a more precise method. The way lath and plaster is constructed it makes it impossible to use a conventional stud finder. My first problem area is finding the studs.

#Do lath and plaster walls have studs how to

Yes, I did a search and just found mentionings of lath and plaster but no concrete information on how to wall mount this beast. I am going to be mounting my new TH-50PH9UK in my bedroom where the walls are lath and plaster construction. I mounted my old(er) TH-50PH9Uk in a new part of the house where the walls are drywall. Originally Posted by ptysell /forum/post/0